Two Sided Heart

by Mrballeng in Craft > Jewelry

13696 Views, 160 Favorites, 0 Comments

Two Sided Heart

IMG_4318.JPG
IMG_4319.JPG
IMG_4330.JPG
IMG_4324.JPG
Silver look on one side, gold look on the other.

This my second soldering project. Figuring out the process was tough but the soldering wasn’t. If you’ve never soldered, don’t be intimidated. It’s much easier than you think.

See how I got set up with the link below.

https://www.instructables.com/id/Phillips-Head-Stud-Earrings/

Find Your Metals

IMG_4263.JPG
IMG_4264.JPG
I’m using a hobby sheet of brass from the hardware store and a piece of a paint rolling pan.

The brass was about $5.00 and came in a .046”X4”X10” sheet. I think I paid $1.50 for the paint rolling pan. You’ll also need a coat hanger.

Form the Wire Heart

IMG_4272.JPG
IMG_4265.JPG
IMG_4266.JPG
IMG_4267.JPG
IMG_4268.JPG
IMG_4269.JPG
IMG_4270.JPG
IMG_4271.JPG
Find a form to make a large circle. I used a quart paint can. Roll a section of coat hanger around the can so you have a circular shape formed in the wire. This step helps the heart look more rounded and less like a triangle under two circles.

Next make a 90 degree bend in the wire. Hammer the wire while it’s in the pliers to sharpen the bend. Use a socket bit and form the lobes of the heart. The exact sizes I’m using aren’t important. Make the heart whatever size you want for the tools you have.

Play with the shape until your happy with it. Then cut the free ends of the wire from the heart.

Make the Relief

IMG_4282.JPG
IMG_4273.JPG
IMG_4274.JPG
IMG_4277.JPG
IMG_4278.JPG
IMG_4279.JPG
IMG_4280.JPG
IMG_4284.JPG
I used aluminum tape but only because that's what I had on hand. Any other heavy tape will work as well. Tape the heart on the metal and place it wire side up on a scrap piece of wood. Evenly hammer the wire all the wall around. When you turn the heart over you’ll see the embossed heart.

Now with the metal side up, use a the peen side of a small hammer to rub the depression in. You only need moderate presure. Do this until the depression is smooth and even.

Use heavy scissors to cut the hearts out. One heart will be cut to size while the other is left just a little larger. This will help during soldering.

Solder

IMG_4289.JPG
IMG_4285.JPG
IMG_4286.JPG
IMG_4287.JPG
IMG_4288.JPG
Apply flux to the inside edges of both of the hearts.

Line up the hearts and lightly clamp them together.

Lay a piece of solder in the seem. Bond the pieces together with a torch. Do this all the way around.

Polish

IMG_4298.JPG
IMG_4297.JPG
IMG_4290.JPG
IMG_4291.JPG
IMG_4292.JPG
IMG_4293.JPG
IMG_4294.JPG
IMG_4295.JPG
Grind off the seam and any excess solder with a rotary tool. Don’t get too crazy here because the metal is thin and you could perforate it.

Sand out any low spots with 1000 and 2000 grit sand paper. Finish the polish with polishing compound and a buffing wheel.

Add the Jump Ring

IMG_4305.JPG
IMG_4300.JPG
IMG_4303.JPG
IMG_4304.JPG
IMG_4318.JPG
IMG_4319.JPG
IMG_4330.JPG
Using a paper clip and cone nose pliers, form a circle in a free end. Cut it free from the rest of the clip and place an almost 180 degree bend in it. Cut the clip so that it tightly meets the loop as shown. Place a section of wire in the open end and pinch the bend tight. See the pictures.

Drill a hole in-between the lobes and insert the jump ring.

Repolish if needed.

If you want to solder the jump ring in, do it before the grinding step. If you do it during this step you may melt out the solder from the polished seams.