Audiono Smart Car Instructions

by obrienk24 in Workshop > Cars

539 Views, 0 Favorites, 0 Comments

Audiono Smart Car Instructions

Screen Shot 2020-05-14 at 10.35.10 am.png

For building the Audiono Smart Car you will need the following material/supplies:

- 2 x motors (yours will have soldered black and red wires on them)

- 2 x large yellow wheels and tyres - free-rotating castor wheel

- Battery pack (4 x AA batteries)

- Arduino Uno (clone)

- Motor shield

- Switch

- Screws, bolts, nuts and spacers

- Various Wires

- 1594 USB cable to A/B port (blue cable)

- 1x ultrasonic sensor - 1x servo unit with wiring

- Plastic servo connectors

Check You Have All the Materials That You Need.

Screen Shot 2020-05-14 at 10.05.35 am.png

Place the 1 Acrylic Bracket Into the Side Slit in the Acrylic Frame. Then Place the Motor Next to It on the Outside and Place Another Acrylic Bracket on the Other Side.

Screen Shot 2020-05-14 at 10.21.26 am.png

Once You Have Done That Place 2 Long Screws Through the Holes That Line Up and Add a Bolt at the Other End and Tighten With a Screwdriver.

Screen Shot 2020-05-14 at 10.22.02 am.png

Then Repeat Steps 2 and 3 on the Opposite Side.

Screen Shot 2020-05-14 at 10.22.30 am.png

Then Add the Sensor Spindles and Slide Them Onto the White Parts of the on the Inside Part of the Motor.

Screen Shot 2020-05-14 at 10.22.30 am.png

Then Grab Your Switch and Attach It Through the Back of the Plastic Frame and in the Hole in the Middle.

Screen Shot 2020-05-14 at 10.24.02 am.png

Then Spin the Acrylic Frame Back Around and Place the Free-rotating Castor Wheel at the Back of the Frame in the Middle So That It Lines Up With the 4 Holes in a Square.

Screen Shot 2020-05-14 at 10.25.05 am.png

Next, You Want to Grab 4 Small Gold Cylinder-like Things and Place Them Under the Free-rotating Castor Wheel in Line With the Four Holes.

Screen Shot 2020-05-14 at 10.26.02 am.png

Then Get 4 Small Screws and Screw Them Into the Four Corners of the Free-rotating Caster Wheel So It Goes Through the Gold Things and Is Secured to the Frame.

Screen Shot 2020-05-14 at 10.27.07 am.png

Then Get Your Large Yellow Wheels and Link the Wheel to the White Part on the Outside of the Motor, Do This on Both Sides.

Screen Shot 2020-05-14 at 10.27.41 am.png

Then Grab Your Black Battery Pack and Place It on the Back of the Acrylic Frame in the Centre Under the Switch.

Screen Shot 2020-05-14 at 10.28.20 am.png

Get 2 Small Screws and Put Them in the Holes on Either Side of the Battery Pack and Fasten With a Screwdriver.

Screen Shot 2020-05-14 at 10.28.53 am.png

Then Get 2 Nuts and Secure the Small Screws on the Other Flip Side of the Frame.

Screen Shot 2020-05-14 at 10.29.28 am.png

Once You Have Done That You Will Place the Wires Like in the Diagram Provided and Peel Off the Paper on the Frame.

Screen Shot 2020-05-14 at 10.29.59 am.png

Once That Is Done You Get Your Double a Batteries and Place One in Each Slot of the Battery Pack, Flip the Switch and You Have the Base of Your Car.

Screen Shot 2020-05-14 at 10.30.35 am.png

Once You Have Assembled the Car Follow the Wiring Diagram to Assemble the Wires to the Car.

Screen Shot 2020-05-14 at 10.31.02 am.png